This video delivers a concise, expert-led guide specifically tailored for wired motorized roller shades, teaching you how to adjust programming settings and troubleshoot common operational issues. Viewers will learn how to enter programming mode to set precise upper and lower limits, reset to factory defaults, and diagnose problems like unresponsive controls or misaligned stops—all using clear visuals and practical steps.
In this video we’ll go over programming your wired roller shade and common troubleshooting tips.
To adjust the upper limit, run the shade to its current upper limit. Hold the UP and DOWN buttons simultaneously until the shade jogs one time. Using the UP or DOWN buttons, move the shade to the desired limit. The shade should be moving incrementally. Once the shade is at the desired limit, Hold the MY button until the shade jogs
one time. Repeat this process for the lower limit. To set a favorite or MY position, move the shade using the UP or DOWN button. Stop the shade with the MY button in the desired position. Press and hold the MY button until the shade jogs one time. You may now access the MY position by briefly pressing the MY button when the shade is stationary. You can delete this MY position by moving to the MY position and holding the MY button until the shade jogs one time. To copy programming to a new channel on an existing or new transmitter. select the current channel you wish to copy. Hold the PROGRAM button on the transmitter until the shade jogs one time. Then select the new channel you wish to copy to. Briefly press the transmitters PROGRAM button and the shade will jog one time. To delete programing from a channel, select the channel you want to remain programmed. Press and hold the transmitters PROGRAM button until the shade jogs one time. Then select the channel you want deleted. Briefly press the program button and the shadewill jog one time.
To factory reset an AC motor, you will need to perform a double power cut. Start by removing the motor from power for 4 seconds. Then return power to the motor for 8 seconds. Remove from power for another 4 seconds. Then return power again. The shade will jog one time. If the shade did not start the double power cut at an end limit, the motor will run for roughly 3 seconds then stop. Press and hold the PROGRAM button on a transmitter until the motor jogs two times. The motor settings and paired transmitters are now erased. If the motor does not jog twice, repeat these steps. Hold the UP and DOWN buttons on a transmitter to re-pair the motor.
To factory reset IQM-DCR motors, press and hold the PRGORAM button on the motor head, with a paperclip, until the shade jogs up and down three times. All the motor settings and paired transmitters are now erased. Then hold the UP and DOWN buttons on a transmitter,
to re-pair to the motor. To delete all paired transmitters without losing shade limits, Press and hold the PROGRAM button on the motor head, with a paperclip, until the shade jogs two times.
To factory reset IUQ-DCR motors, you will need the reset tool. Use the reset tool to press
and hold the three buttons on the motor head, until the shade jogs up and down three times. All motor settings and paired transmitters are now erased. Then hold the UP and DOWN buttons on a transmitter to re-pair to the motor.
To modify the motor rotation after performing a factory reset, use the UP or DOWN button to move the shade away from its end limits. Then press and hold the MY button until the shade jogs one time. Using the UP or DOWN buttons, verify the motor rotation. You will now need to set your limits.
To set limits during a factory reset, use the UP or DOWN buttons on the transmitter to position the shade at the desired upper limit. When the desired upper limit position is reached, Briefly press the MY and DOWN buttons simultaneously to set the upper limit. The shade will begin to move down to the lower limit. Allowing the shade to run down towards its lower limit, use the MY button to stop the shade and use the UP or DOWN buttons to position the shade to the desired lower limit. Briefly press the UP and MY buttons simultaneously on the transmitter to set the lower limit. Allow the shade to run up to the upper limit that was previously set. To confirm both limits, press and hold the MY button. The shade will briefly jog up and down one time. To finalize, briefly press the PROGRAM button on the transmitter. The shade will briefly jog up and down one time.
And that’s it. Thanks for watching. Check out our other videos for more helpful tips.